SMG104 IP/MPLS Router
SMG104 IP/MPLS Router
Simgenet SMG104 is a modular IP/MPLS router platform running on the in-house developed SMGOS software. Designed for telecom, ISP and critical infrastructure networks with Segment Routing, MPLS-TE, BGP and IEEE 1588 PTP v2 support.
Modular IP/MPLS Platform for Service Providers and Critical Infrastructures
SMG104 is built on SMGOS, designed from scratch by Simgenet engineers. No third-party router software is used; protocol behavior, CLI outputs and all service logic are entirely under Simgenet control. This architecture enables customization, rapid updates and local technical support.
Thanks to its Cisco IOS-like CLI structure, existing network teams can master the platform without additional training. Full configuration support is also available through the web-based management interface.
In-House Developed SMGOS IP/MPLS Software Infrastructure
SMGOS, running on SMG104, is an IP/MPLS routing operating system fully developed in-house by Simgenet.
- No dependency on third-party routing software
- Provides full control, customizability and long-term sustainability
- Features an architecture optimized for critical infrastructure and service provider networks
SMGOS is designed to respond to changes in network topology at millisecond level.
Protocol and Service Support
SMG104 offers a wide range of protocols and services through the SMGOS infrastructure:
- Routing: OSPFv2, OSPFv3, IS-IS, BGP (iBGP/eBGP/RR), BGP Add-Path, RIPv2
- MPLS: LDP, MPLS L3 VPN (RFC 4364), MPLS L2 VPN / EoMPLS, Segment Routing (SR-MPLS), MPLS-TE / RSVP-TE
- Layer 2: VLAN, Q-in-Q, LACP, STP/RSTP/MSTP, LLDP, VXLAN
- Services: QoS / Traffic Shaping, DHCP Server/Relay, NAT (SNAT/DNAT/PAT/VRF-aware), PPPoE
- VPN: IPsec VPN (Site-to-Site), OpenVPN, VRF
- Time: IEEE 1588v2 PTP — T-GM / Boundary Clock (G.8275.1/.2, 61850, PRTC-A), NTP/SNTP (GNSS Stratum-1)
- Management: SNMP v2/v3, RADIUS (AAA), Syslog, SSH, NETCONF
- High Availability: BFD, Fast Convergence, ECMP
Modular Hardware Architecture
SMG104 features 4 PCIe Gen3 x8 slots in a 1U rackmount form factor. This modular architecture offers:
- 1G / 10G / 25G / 40G / 100G Ethernet card combinations
- Configurable slot architecture with fiber and copper Ethernet cards
- Application-specific port and card configurations
This architecture provides a flexible design for service providers and critical infrastructures where capacity requirements can change over time.
Control Plane and System Resources
- Intel® Xeon® E3-1200 v5 series processor
- Up to 64 GB DDR4 memory (4× DDR4-2133 MHz DIMM)
- Control plane optimized for intensive routing and MPLS scenarios
Industrial Durability and Field Suitability
- EMC Level 3 industrial durability (TS/EN 61000-4 Level 3)
- Operating temperature: -20°C ~ +60°C
- CE (EMC/LVD), RoHS certifications
- 220 VAC, 250W Industrial PSU
- 1U Rackmount, 19-inch standard rack — 430 × 550 × 89 mm / 20 kg
- Console / Management: RS-232, USB, RJ45 Mgmt
Ethernet Card Options
Each PCIe Gen3 x8 slot independently accepts cards of different speeds and interface types. 1G, 10G, 40G and 100G cards can be used together on the same platform.
| Model | Port Structure | Speed | Description |
|---|---|---|---|
| SMG3500PF-8SFP-M | 8× SFP | 1G | Fiber, Standard |
| SMG3500PF-4SFP-M | 4× SFP | 1G | Fiber, Standard |
| SMG3500PT-8T-M | 8× RJ45 | 1G | Copper, Standard |
| SMG3500BP-8T-M | 8× RJ45 | 1G | Copper, Bypass |
| SMG3501PT-4T-M | 4× RJ45 | 1G | Copper, Standard |
| SMG3501BP-4T-M | 4× RJ45 | 1G | Copper, Bypass |
| SMG5991PF-2SFP-M | 2× SFP+ | 10G | Fiber |
| SMG7100PF-2QSFP-M | 2× QSFP+ | 40G | Fiber |
| SMG8100PF-2QSFP-M | 2× QSFP+ | 100G | Fiber * |
* 100G card is supported. Maximum simultaneous throughput is limited by the PCIe Gen3 backplane capacity (~126 Gbps Full-Duplex theoretical per slot).
Maximum Port Capacity: 32× 1G / 8× 10G / 4× 25G / 4× 100G (configuration dependent)
Application Areas
- Telecom & ISP — Edge / aggregation node, Metro Ethernet backbone, service provider infrastructure in PE/PEN roles
- Energy Transmission (154/400 kV) — TEİAŞ RTU communication networks, SCADA IP/MPLS transport
- Transformer Substations — 154/400 kV inter-substation IP/MPLS communication infrastructure
- Railway — IP/MPLS transport infrastructure for GSM-R, FRMCS and ETCS based railway systems
- SCADA & Industrial — Industrial automation network backbone, SCADA remote access infrastructure
- Government & Critical Infrastructure — Secure communication networks, national critical infrastructure projects
- Data Center Edge — DC edge, WAN aggregation, enterprise network gateway
All Simgenet router platforms feature TS/EN 61000-4 Level 3 industrial EMC durability and -20°C ~ +60°C extended operating temperature range.
Technical Comparison Table
| Feature | SMG411 Edge Router |
SMG104 Aggregation |
SMG818V5 Industrial |
SMG1000 Industrial |
|---|---|---|---|---|
| HARDWARE PLATFORM | ||||
| Operating System | SMGOS | SMGOS | SMGOS | SMGOS |
| Chipset / Platform | Intel | Intel C236 | Intel® C741 | ICX 4309Y |
| CPU | Intel | Intel Xeon E3-1200 v5 | Xeon 5418Y | Xeon ICX 4309Y |
| Memory (RAM) | 16 GB | Max. 64 GB DDR4 | 16x DDR5 ECC | 16x DDR5 ECC |
| Form Factor | 1U Rackmount | 1U Rackmount | 2U Rackmount | 4U Rackmount |
| Dimensions | N/A | 430×550×89 mm | 440×592×88 mm | N/A |
| Power Supply | 220 VAC, 250W | 220 VAC, 250W | 2x 220 VAC, 250W | 2x 220 VAC, 250W |
| Operating Temperature | -20°C ~ +60°C | -20°C ~ +60°C | -20°C ~ +60°C | -20°C ~ +60°C |
| EMC Certification | CE, RoHS, TS/EN 61000-4 Level 3 | CE, RoHS, TS/EN 61000-4 Level 3 | TS/EN 61000-4 Level 3 | TS/EN 61000-4 Level 3 |
| EXPANSION & PORTS | ||||
| PCIe Slot | PCIe based | 4x PCIe Gen3 x8 | 8x PCIe Gen5 x8 | Model A: 1x / Model B: 2x PCIe Gen4 |
| Max. Uplink Speed | 10G | 100G | 100G | 200G |
| Max. Ethernet Ports | Fixed configuration | 32x 1G / 8x 10G / 4x 25G | 64x 1G / 16x 10G / 8x 25G / 4x 100G | 80x 1G / 24x 10G / 8x 100G |
| Console / Management | RS-232, USB, RJ45 Mgmt | RS-232, USB, RJ45 Mgmt | RS-232, USB, RJ45 Mgmt | RS-232, USB, RJ45 Mgmt |
| ROUTING & MPLS | ||||
| Statik Route / PBR | ✓ | ✓ | ✓ | ✓ |
| RIPv2 | ✓ | ✓ | ✓ | ✓ |
| OSPFv2 / OSPFv3 | ✓ | ✓ | ✓ | ✓ |
| IS-IS | ✓ | ✓ | ✓ | ✓ |
| BGP (iBGP / eBGP / RR) | ✓ | ✓ | ✓ | ✓ |
| BGP Add-Path | ✓ | ✓ | ✓ | ✓ |
| MPLS / LDP | ✓ | ✓ | ✓ | ✓ |
| MPLS L3 VPN (RFC 4364) | ✓ | ✓ | ✓ | ✓ |
| MPLS L2 VPN / EoMPLS | ✓ | ✓ | ✓ | ✓ |
| Segment Routing (SR-MPLS) | ✓ | ✓ | ✓ | ✓ |
| MPLS-TE / RSVP-TE | ✓ | ✓ | ✓ | ✓ |
| VRF | ✓ | ✓ | ✓ | ✓ |
| VXLAN | ✓ | ✓ | ✓ | ✓ |
| Fast Convergence / ECMP | ✓ | ✓ | ✓ | ✓ |
| BFD | ✓ | ✓ | ✓ | ✓ |
| SERVICES & SECURITY | ||||
| QoS / Traffic Shaping | ✓ | ✓ | ✓ | ✓ |
| DHCP Server / Relay | ✓ | ✓ | ✓ | ✓ |
| NAT (SNAT/DNAT/PAT/VRF-aware) | ✓ | ✓ | ✓ | ✓ |
| IPsec VPN (Site-to-Site) | ✓ | ✓ | ✓ | ✓ |
| OpenVPN | ✓ | ✓ | ✓ | ✓ |
| PPPoE | ✓ | ✓ | ✓ | ✓ |
| IEEE 1588 PTP v2 | ✓ | ✓ | ✓ | ✓ |
| NTP / SNTP | ✓ | ✓ | ✓ | ✓ |
| SNMP v2/v3 | ✓ | ✓ | ✓ | ✓ |
| RADIUS (AAA) | ✓ | ✓ | ✓ | ✓ |
| Syslog | ✓ | ✓ | ✓ | ✓ |
Which Model Should You Choose?
All models run the same SMGOS software and the same protocol set. Model selection should be based not on software capabilities, but on environmental durability requirements, port/uplink capacity and physical space.
Criterion 1: Environmental Conditions
| SMG411 / SMG104 | SMG818V5 / SMG1000 | |
|---|---|---|
| Environment | Controlled room, data center, air-conditioned cabinet | Transformer substation, field cabinet, open area, railway station |
| Temperature | -20°C ~ +60°C | -20°C ~ +60°C |
| EMC Level | TS/EN 61000-4 Level 3 | TS/EN 61000-4 Level 3 |
| Result | All models EMC Level 3 compliant | All models EMC Level 3 compliant |
Criterion 2: Port / Uplink Capacity
| SMG411 | SMG104 | SMG818V5 | SMG1000 | |
|---|---|---|---|---|
| PCIe Slot | Limited | 4x Gen3 | 8x (Gen5) | Model A: 5× Gen4 / Model B: 10× Gen4 |
| Max. Speed | 10G | 100G | 100G | 200G |
| Suitable Scenario | Few ports, low bandwidth | Medium-high ports, multiple uplink | High port density, multiple cards | High port density, multiple cards |
Criterion 3: Physical Space
| SMG411 | SMG104 | SMG818V5 | SMG1000 | |
|---|---|---|---|---|
| Form Factor | 1U Rackmount | 1U Rackmount | 2U Rackmount | 4U Rackmount |
| Note | Narrow cabinet, limited space | Standard rack | More card capacity | More card capacity |
Built-in SIP Server (VoIP)
Thanks to the Asterisk-based built-in SIP Server running on the SMGOS operating system, the router can also function as a basic IP telephone exchange. In locations without a telephone exchange, SIP numbers obtained from the ISP can be directly assigned to the router for VoIP communication.
- Unlimited SIP Extensions: Any number of internal lines can be defined as needed
- ISP SIP Trunk Integration: Directly integrates with SIP numbers obtained from the service provider
- Basic PBX Functions: Internal calls, call forwarding, dial plan support
- Management: Configuration via CLI (Web interface is under development)
| Hardware Platform | |
|---|---|
| Operating System | SMGOS (Simgenet in-house developed IP/MPLS NOS) |
| Form Factor | 1U Rackmount |
| Platform / Chipset | Intel® C236 |
| Processor (CPU) | Intel® Xeon® E3-1200 v5 series |
| Memory (RAM) | 4 × DDR4 DIMM, DDR4-2133 MHz, up to 64 GB total |
| Expansion Architecture | 4× PCIe Gen3 x8 |
| Power Supply | 1× 220 VAC server-class power supply (industrial type), 250 W |
| Backplane Capacity (Theoretical, PCIe-Based) | |
| Per-Slot Theoretical (FD) | ≈ 126 Gbps |
| Total Theoretical Backplane (FD) | ≈ 504 Gbps |
| Note | Theoretical values are not a performance guarantee; they depend on packet size and service load. |
| Modular Ethernet Card Architecture | |
| Supported Speeds | 1G / 10G / 40G / 100G Ethernet modules |
| Interface Options | SFP / SFP+ / QSFP+ / QSFP28 |
| Example Modules | SMG3500PF-4SFP-M, SMG7100PF-4SFP+-M, SMG8100PF-2QSFP28-M |
| Routing Protocols | |
| Basic Routing | Static, Default, Policy-Based Routing (PBR), Route Redistribution |
| NAT | SNAT, DNAT, PAT, VRF-aware NAT |
| IGP | RIP v2, OSPFv2, OSPFv3, IS-IS (L1/L2), IS-IS Wide Metrics |
| BGP | iBGP/eBGP, Multipath, ECMP, Communities, Extended Communities, Add-Path, Flowspec, Graceful Restart/Shutdown |
| IP Address Management | DHCP Server/Relay, VRF-aware, IPv4/IPv6 Dual-Stack, ARP, IPv6 ND |
| MPLS and Advanced MPLS | |
| MPLS Core | IP MPLS, MPLS LDP, Label Push/Pop/Swap, PHP, TTL Propagation |
| MPLS VPN | L2VPN (VPWS, VPLS), L3VPN, VRF-based MPLS services |
| IPsec VPN | IKEv2; encrypted WAN / VTI tunnel |
| Site-to-Site VPN | branch-to-branch encrypted connectivity via IPsec/VTI |
| Remote Access VPN | OpenVPN server |
| Segment Routing | SR-MPLS, TI-LFA, OSPFv2/IS-IS SR Extensions |
| Traffic Engineering | MPLS-TE, RSVP-TE, Constraint-based Path, Explicit/Dynamic LSP |
| Protection / OAM | MPLS FRR (Facility Backup, One-to-One Backup), Y.1731, CFM |
| Fast Convergence and Redundancy | |
| Fast Convergence | Millisecond-level re-routing |
| ECMP | Equal-Cost Multi-Path traffic distribution |
| BFD | Bidirectional Forwarding Detection |
| Time Synchronization | |
| PTP | IEEE 1588-2008 PTP v2 — T-GM (Grandmaster) / T-BC (Boundary Clock) / Ordinary Clock; reboot-free BC↔GM (BMCA) |
| PTP Profiles | ITU-T G.8275.1 (L2, E2E, domain 24–43) · G.8275.2 (L3/UDP-IPv4, E2E, 44–63) · IEC/IEEE 61850-9-3 power (P2P, 0–127) — profile auto-locks layer & delay mechanism |
| Delay Mechanism | End-to-End (E2E, G.8275) and Peer-to-Peer (P2P, 61850) |
| PTP Timestamping | Hardware (HW) timestamping on data ports |
| Grandmaster Class | ITU-T G.8272 PRTC-A (≤100 ns); clockClass 6 (GNSS/PPS locked), 2-step, currentUtcOffset 37 s |
| PTP Accuracy | ITU-T G.8273.2 Class-A; measured GNSS RMS ~19–21 ns, maxTE 38 ns; G.8271 / G.8271.1 network limits |
| Time Source | GNSS grandmaster (clockClass 6 locked, primary) · multi-domain (per-port) · NTP/SNTP fallback |
| NTP / SNTP | Stratum-1, GNSS-disciplined (Meinberg ref); client and server |
| Network Management, Monitoring and Security | |
| Management Interface | CLI (Cisco IOS-like command line) |
| Management | SNMP, Syslog, RADIUS (AAA) |
| Security | ACL (IPv4/IPv6), QoS/DiffServ (DSCP, policing, shaping), LLDP, LACP (802.3ad) |
| Overlay and Virtualization | |
| VXLAN | Supported — Overlay network architecture compatibility |
| VoIP / SIP Server | |
| SIP Server | Built-in Asterisk-based SIP Server |
| SIP Extension | Unlimited SIP extensions can be defined |
| SIP Trunk Integration | Integrates with ISP SIP numbers |
| Basic PBX Function | Internal calling, call forwarding, dial plan |
| SIP Termination | SIP lines received from ISP terminate directly on the router; no additional termination hardware required |
| PBX Forwarding | Calls can be forwarded to existing customer PBX system via the router |
| Standalone PBX Mode | Operates as a basic IP PBX in locations without an existing PBX |
| Management | CLI-based configuration (Web interface under development) |
| Environmental Conditions and Certifications | |
| Operating Temperature | -20°C ~ +60°C |
| Storage Temperature | -20°C ~ +75°C |
| Relative Humidity | %10 ~ %95 (non-condensing / non-condensing) |
| EMC Emission | TS EN 55032:2015+A11:2020 (Class A) |
| EMC Immunity | TS EN 55035:2017+A11:2020 |
| ESD (IEC 61000-4-2) | Level 3 |
| Radiated RF (IEC 61000-4-3) | Level 3 |
| EFT/Burst (IEC 61000-4-4) | Level 3 |
| Surge (IEC 61000-4-5) | Level 3 |
| Conducted RF (IEC 61000-4-6) | Level 3 |
| Magnetic Field (IEC 61000-4-8) | Level 3 |
| Voltage Dips (IEC 61000-4-11) | Level 3 |
| Harmonics | TS EN IEC 61000-3-2:2019+A1:2021 |
| Flicker | TS EN 61000-3-3:2013+A2:2021 |
| LVD | TS EN 62368-1:2020+A11:2020 |
| RoHS | TS EN IEC 63000:2018 |
| EU Directives | 2014/30/AB (EMC), 2014/35/AB (LVD), 2011/65/AB+2015/863/AB (RoHS) |
| Positioning | |
| Target Segment | 1U compact IP/MPLS Router — Edge & Aggregation |
| Application Areas | Telecom/ISP, Energy Transmission (154/400 kV), Transformer Substations, SCADA, Railway (GSM-R/FRMCS/ETCS), Critical Infrastructure |
For detailed technical information, please refer to the product datasheet or hardware user manual.